IPv6 operations J. Linkova Internet-Draft Google Updates: 8585 (if approved) T. Jensen Intended status: Informational Microsoft Expires: 24 April 2025 21 October 2024 464XLAT Customer-side Translator (CLAT): Node Recommendations draft-ietf-v6ops-claton-02 Abstract 464XLAT [RFC6877] defines an architecture for providing IPv4 connectivity across an IPv6-only network. The solution contains two key elements: provider-side translator (PLAT) and customer-side translator (CLAT). This document complements [RFC6877] and updates [RFC8585] by providing recommendations for the node developers on enabling and disabling CLAT functions. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on 24 April 2025. Copyright Notice Copyright (c) 2024 IETF Trust and the persons identified as the document authors. All rights reserved. Linkova & Jensen Expires 24 April 2025 [Page 1] Internet-Draft claton October 2024 This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/ license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Requirements Language . . . . . . . . . . . . . . . . . . . . 3 3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3 4. Multiple Interfaces Considerations . . . . . . . . . . . . . 4 5. Enabling CLAT . . . . . . . . . . . . . . . . . . . . . . . . 4 6. Disabling CLAT . . . . . . . . . . . . . . . . . . . . . . . 5 7. CLAT Addresses Considerations . . . . . . . . . . . . . . . . 6 7.1. CLAT IPv4 Addresses . . . . . . . . . . . . . . . . . . . 6 7.2. CLAT IPv6 Addresses . . . . . . . . . . . . . . . . . . . 7 7.2.1. CLAT and Multiple Prefixes per Interface . . . . . . 8 8. MTU Considerations . . . . . . . . . . . . . . . . . . . . . 9 9. Updates to RFC8585 . . . . . . . . . . . . . . . . . . . . . 9 10. Security Considerations . . . . . . . . . . . . . . . . . . . 11 11. Privacy Considerations . . . . . . . . . . . . . . . . . . . 11 12. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 12 13. References . . . . . . . . . . . . . . . . . . . . . . . . . 12 13.1. Normative References . . . . . . . . . . . . . . . . . . 12 13.2. Informative References . . . . . . . . . . . . . . . . . 13 Appendix A. Enabling and Disabling CLAT: Flowchart . . . . . . . 14 Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . . 15 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 15 1. Introduction 464XLAT is widely deployed in 3GPP networks (as described in Section 4.2 of [RFC6877]) where User Equipment (UE) devices (such as mobile phones and CE routers) perform the CLAT function, providing a private IPv4 address and default route for the applications and tethered devices. Enabling 464XLAT allowed mobile operators to transition UE devices to IPv6-only mode, where those devices are only assigned IPv6 addresses on their WAN interfaces. Until recently, IPv6-only hosts were rather uncommon outside of mobile networks and datacenters. Even if the network provides PLAT in the form of NAT64 ([RFC6146]), hosts (desktops, laptops etc) still needed the network to provide IPv4 addresses, as otherwise IPv4-only applications fail. However, as more and more operating systems Linkova & Jensen Expires 24 April 2025 [Page 2] Internet-Draft claton October 2024 outside of the 3GPP world support CLAT, it becomes possible to migrate those devices to IPv6-only mode, while still providing IPv4 as a service via 464XLAT. Networks such as public Wi-Fi, enterprise networks or even home networks can deploy 464XLAT as described in Section 4.2 of [RFC6877]: * PLAT functions are performed by NAT64 network devices. * CLAT is performed by the UA itself. Another 464XLAT deployment model is a Wireline one (section 4.1 of [RFC6877]), when a CPE router is connected to an IPv6-only network and provides CLAT functions for IPv4-enabled downstream devices. [RFC8585] specifies 464XLAT support requirements for such devices. For both scenarios to work, the node performing CLAT (such as a host or a CPE router) need to enable the CLAT when connecting to an IPv6-only network. This document complements [RFC6877] and updates [RFC8585] by providing recommendations for the node developers on enabling and disabling CLAT functions. 2. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. 3. Terminology This document reuses most of Terminology section from [RFC6877]. * CLAT Node: a node (a host or a router) which performs CLAT functions by running one or multiple CLAT instances (e.g. one CLAT instance per interface). * IPv6-only network: A network that does not assign IPv4 addresses to hosts and facilitates connectivity to IPv4-only destinations using NAT64 ([RFC6146]). In this document, the term "IPv6-only network" specifically refers to networks that provide NAT64 as it's required by the 464XLAT architecture ([RFC6877]). * Native IPv4 (such as in 'native IPv4 connectivity' or 'native IPv4 default gateway'): IPv4 connectivity or default gateway provided by the network without using any form of IPv4-as-a-service or translation mechanisms (such as 464XLAT). Linkova & Jensen Expires 24 April 2025 [Page 3] Internet-Draft claton October 2024 Currently the only avalable form of PLAT for 464XLAT deployments is NAT64. Therefore this document uses those terms interchangeably. 4. Multiple Interfaces Considerations A node may have multiple IPv6-only interfaces (for example, a mobile phone can be connected to an IPv6-only Wi-Fi network and to an IPv6-only mobile network). In that case the node SHOULD run an independent, dedicated CLAT instance on each interface connected to a network equipped with PLAT. Consequently, each CLAT instance SHOULD install a separate default IPv4 route on each CLAT-enabled interface. The metrics of IPv4 routes SHOULD be consistent with the metrics of IPv6 default routes. 5. Enabling CLAT For performance and security reasons CLAT MUST NOT be enabled if the node has IPv4 native connectivity over the given interface. Therefore recommendations provided in this section are only applicable to an IPv6-only node (a node which does not have a native IPv4 default route configured). To enable CLAT, an IPv6-only node needs to discover the PLAT-side translation IPv6 prefix, also known as the NAT64 prefix (see Section 6.3 of [RFC6877]). The PREF64 Router Advertisement (RA) option ([RFC8781]) provides that information and can be used as a strong indication that the network supports PLAT (NAT64) functionality. Therefore an IPv6-only node SHOULD enable CLAT as soon as an Router Advertisement containing PREF64 option is received. If RAs received by the node do not contain a PREF64 option, the node MAY use other mechanisms to detect the PLAT presence and obtain the NAT64 prefix (such as [RFC7050]). When discovering the NAT64 prefix using the mechanism defined in [RFC7050], the node MUST follow recommendations provided in [RFC8880]. Specifically, the node MUST send the query to the DNS servers for the specific network interface per Section 7.1 of [RFC8880]. In particular, queries for AAAA resource records of "ipv4only.arpa." MUST be sent to the recursive resolvers provided by the network, not to the resolvers configured manually, local recursive resolvers etc. Any delay in enabling CLAT on an IPv6-only node would be impactful for IPv4-only applications, as such applications cannot benefit from 464XLAT until CLAT is operational. Therefore it's desirable that the node enables CLAT as soon as network support for PLAT is detected while IPv4 connectivity is not yet detected. The node SHOULD enable CLAT after discovering the NAT64 prefix, unless by that time the node has already obtained a non-link-local IPv4 address. The node SHOULD Linkova & Jensen Expires 24 April 2025 [Page 4] Internet-Draft claton October 2024 NOT wait for an explicit (DHCP Option 108) or an implicit (DHCP timeouts) indication that native IPv4 connectivity is not available. However, to mitigate attacks described in Section 7 of [RFC7050], the node MAY delay enabling CLAT if the NAT64 prefix was discovered via DNS ([RFC7050]) only. The delay is implementation specific. If IPv4 connectivity becomes available later, the node MUST disable CLAT (unless explicitly configured to keep it running) as discussed in the following section. If the node supports multiple IPv4 continuity solutions, the node MUST follow recommendations from Section 4 of [RFC7335] to avoid IPv4 address space conflicts. 6. Disabling CLAT It is possible that after the CLAT instance has started, native IPv4 becomes available (e.g. an IPv4 address received via DHCP). Unless explicitly configured otherwise, the node MUST disable CLAT immediately upon obtaining a native IPv4 default gateway. While disabling CLAT is impactful for all applications and traffic flows already utilizing CLAT, it is recommended not only from performance perspective, but also from security point of view. Because IPv4-only networks are inherently IPv6-ignorant, they might lack IPv6 layer2 security features, such as RA Guard, that would prevent spoofed RAs. An attacker can send an RA containing the PREF64 option, while the network doesn't provide any PLAT functionality. If the node keeps CLAT enabled and uses it for IPv4-only destinations, that traffic could be dropped (availability attack) or routed through an attacker-controlled route (active attack on insecure traffic or hoarding secure traffic for "Harvest Now, Decrypt Later" attacks for non-PQC secure traffic, see Section 8 of [I-D.ietf-pquip-pqc-engineers]). Rogue RAs can also disturb traffic to destinations that support both IPv4 and IPv6 by causing IPv6 through an attacker's PLAT to be used instead of the legitimate network owner's IPv4 path. There are some corner cases when the administrator might prefer the node to use CLAT even if the native IPv4 connectivity is available (e.g. for performance reasons, if IPv4 as a Service performs better than native IPv4). However for the reasons described above such behaviour MUST be explicitly enabled by the administrator via a configuration knob and MUST NOT be a default behaviour, especially for unmanaged nodes. Linkova & Jensen Expires 24 April 2025 [Page 5] Internet-Draft claton October 2024 7. CLAT Addresses Considerations 7.1. CLAT IPv4 Addresses There are two different models in 464XLAT deployments: * A dedicated prefix model, which Section 4.1 of [RFC6877] calls "wireline network architecture". In that case, the node performing CLAT functions also extends the network downstream and provides network connectivity services to other connected systems. Those systems can be physical (e.g. various clients connected to a CPE router), or logical (e.g. virtual systems running on a node, while the host system acts as a router and performs CLAT). In all those cases, systems behind the CLAT node usually use [RFC1918] addresses. Despite the word "wireline", this architecure is applicable for wireless or 3GPP routers: such router can provide IPv4 connectivity to connected devices, performing CLAT functions for traffic sent/received via the IPv6-only uplink interface. * A single-address model, which section 4.2 of [RFC6877] calls "wireless network architecture". In that case, the CLAT instance provides an IPv4 address and the default route to the local node's network stack only. It should be noted that [RFC6877] implies that the second deployment scenario is limited to 3GPP cases, while currently it is also deployed in other types of networks, such as enterprise networks and Wi-Fi hotspots, where hosts (as mobile phones, laptops and desktops) use CLAT to provide connectivity to IPv4-only local applications. Despite the word "wireless" in the name, this architecure is applicable for wired networks as well (e.g. desktops or servers using wired connections). In the single-address model, the CLAT instance needs a single IPv4 CLAT address and a single CLAT-only IPv6 address (which is distinct from the one or more IPv6 addresses used by the node running CLAT for its own native IPv6 connectivity, see Section 7.2). The node providing CLAT functions to local applications SHOULD use IPv4 addresses from the dedicated 192.0.0.0/29 range ([RFC7335]), reserved for IPv4 continuity solutions including but not limited to 464XLAT. If the node runs multiple CLAT instances (see Section 4), the node SHOULD use different local IPv4 addresses for each CLAT instance. This approach limits the number of CLAT instances per node to 8, which seems to be more that sufficient at the time of writing. If in the future some deployment scenarios require more that 8 CLAT instances per node, a new larger IPv4 range will be requested from IANA. The node MUST NOT send packets on wire from the local CLAT address. Linkova & Jensen Expires 24 April 2025 [Page 6] Internet-Draft claton October 2024 The host SHOULD use 255.255.255.255 as a netmask for the CLAT address. That allows all 8 addresses from 192.0.0.0/29 to be used, if needed. It should be noted that 192.0.0.0/29 is shared between multiple IPv4 continuity solutions such as 464XLAT and DS-Lite (see [RFC7335]. For example, Section 10 of [RFC6333] reserves 192.0.0.1 for the Dual- Stack Lite default router. However, as per Section 4 of [RFC7335], the host MUST NOT enable two active IPv4 continuity solutions simultaneously in a way that would cause a node to have overlapping 192.0.0.0/29 address space. Therefore, as long as the host is not using DS-Lite, it MAY use 192.0.0.1 as a CLAT address. 7.2. CLAT IPv6 Addresses Section 6.3 of [RFC6877] recommends that the CLAT instance acquires a dedicated /64 for translating between IPv4 and IPv6, and only uses a single interface IPv6 address if a dedicated prefix is not available via DHCPv6-PD. However, deployments where each node can obtain a dedicated /64 just for CLAT are rather uncommon, especially in environments like enterprise networks, Wi-Fi hotspots, etc. Quite often the CLAT instance uses a single IPv6 address as a source for all IPv4 traffic translated by CLAT. In particular, in a single address model (see Section 7.1) the CLAT instance only need a single CLAT IPv6 address. Even in a dedicated prefix model, the CLAT instance can first perform stateful NAT44 to translate all IPv4 addresses from the dedicated prefix to a single IPv4 address, and then perform stateless CLAT. The CLAT instance SHOULD obtain a dedicated IPv6 address used exclusively for CLAT functions. This is required as when the node receives a packet from a NAT64 source, the node needs to differentiate between native IPv6 traffic and traffic which needs to be passed to the CLAT instance. For example, an ICMPv6 Echo Reply packet from 64:ff9b::203.0.113.1 can be a response to either an IPv6 ping to 64:ff9b::203.0.113.1, or an IPv4 ping to 203.0.113.1, translated by CLAT. Using a dedicated IPv6 source address for CLAT traffic allows the node to make that distinction without keeping state and operate in the stateless mode (see Section 1.3 of [RFC6145]. In a dedicated prefix model, the instance MAY obtain a dedicated IPv6 address for each CLAT IPv4 address. In accordance with Section 5.4 of [RFC4862], the node MUST perform Duplicate Address Detection for each dedicated CLAT address. Linkova & Jensen Expires 24 April 2025 [Page 7] Internet-Draft claton October 2024 If the dedicated CLAT address is obtained via Stateless Address Autoconfiguration (SLAAC, [RFC4862]), the CLAT instance SHOULD ensure that the address is checksum-neutral for the given local IPv4 CLAT address and the NAT64 prefix (this means that the local IPv4 address needs to be assigned/known before the IPv6 address is configured). Using a checksum-neutral CLAT address provides the following benefits: * Better performance as CLAT doesn't need to recalculate the checksum. * If a protocol uses the standard IP checksum, CLAT doesn't need to recalculate the checksum. That improves the chances of the protocol working via CLAT even if CLAT is not aware of the protocol's semantics. The node SHOULD treat SLAAC-generated CLAT addresses as temporary addresses ([RFC8981]). In particular: * The node SHOULD generate new CLAT addresses over time, as described in Sections 3.4 and 3.6 of [RFC8981]. * The node SHOULD generate a different interface id for the CLAT address when connecting to different networks, even if the NAT64 prefix and the local IPv4 CLAT address do not change. To achieve that, the node SHOULD generate a random checksum-neutral CLAT address every time the network attachement changes to another network. 7.2.1. CLAT and Multiple Prefixes per Interface The CLAT instance SHOULD obtain a dedicated IPv6 address (or addresses, if a dedicated prefix model is used) from each global prefix used to configure IPv6 addresses on the given interface. When selecting an address to be used as a source address for the translated packet, the following rules are applied: * All packets with the same IPv4 5-tuple MUST be translated to the same IPv6 address, as long as that address is valid ([RFC4862]) and assigned to the interface. * When translation for a new IPv4 5-tuple is performed by the CLAT instance, the instance SHOULD comply with requirements defined in Section 3 of [RFC8028], in particular Sections 3.2 and 3.3 of [RFC8028]. This is needed to ensure that the CLAT is operational and selects the source IPv6 correctly in multihomed environments or if the link subnet has been changed (renumbered). Linkova & Jensen Expires 24 April 2025 [Page 8] Internet-Draft claton October 2024 8. MTU Considerations The IPv4 header is 20 bytes long (or longer if IP options are present), while the IPv6 header is 40 bytes. This means that when CLAT translates an IPv4 packet to IPv6, it usually adds 20 bytes to the packet size. To minimize undesirable IP fragmentation ([RFC8900]), the CLAT instance in a single-address mode SHOULD present IPv4-only applications with an IPv4 MTU which is 20 bytes smaller than the IPv6 MTU of the interface the instance is running on. 9. Updates to RFC8585 This document makes the following changes to Section 3.2.1 of [RFC8585]: OLD TEXT: === 464XLAT requirements: === NEW TEXT: === 464XLAT requirements: 464XLAT-0: The IPv6 Transition CE Router SHOULD follow recommendations provided in draft-link-v6ops-claton. === OLD TEXT: === 464XLAT-4: The IPv6 Transition CE Router MUST implement [RFC7050] ("Discovery of the IPv6 Prefix Used for IPv6 Address Synthesis") in order to discover the provider-side translator (PLAT) translation IPv4 and IPv6 prefix(es)/suffix(es). === NEW TEXT: Linkova & Jensen Expires 24 April 2025 [Page 9] Internet-Draft claton October 2024 === 464XLAT-4: The IPv6 Transition CE Router MUST implement [RFC8781] ("Discovering PREF64 in Router Advertisements") and SHOULD implement [RFC7050] ("Discovery of the IPv6 Prefix Used for IPv6 Address Synthesis") in order to discover the provider-side translator (PLAT) translation IPv4 and IPv6 prefix(es)/suffix(es). === OLD TEXT: === 464XLAT-6: If the network provides several choices for the discovery/ learning of the NAT64 prefix, the priority to use one or the other MUST follow this order: 1) [RFC7225] and 2) [RFC7050]. The NAT64 prefix could be discovered by means of the method defined in [RFC7050] only if the service provider uses DNS64 [RFC6147]. It may be the case that the service provider does not use or does not trust DNS64 [RFC6147] because the DNS configuration at the CE (or hosts behind the CE) can be modified by the customer. In that case, the service provider may opt to configure the NAT64 prefix by means of the option defined in [RFC7225]. This can also be used if the service provider uses DNS64 [RFC6147]. === NEW TEXT === 464XLAT-6: If the network provides several choices for the discovery/ learning of the NAT64 prefix, the priority to use one or the other MUST follow this order: 1)[RFC7225] 2)[RFC8781] and 3) [RFC7050]. 464XLAT-7: If the IPv6 Transition CE Router performs CLAT functions it SHOULD also include the PLAT prefix in Router Advertisements ([RFC8781]) sent via the LAN interfaces. If the IPv6 Transition CE Router acts as a DHCP server it SHOULD enable DHCP Option 108 ([RFC8925]) processing. The router SHOULD have a configuration knob to disable DHCP Option 108 processing. [RFC8781] allows the service provider to signal NAT64 prefix independently from DNS64 presence. At the same time the NAT64 prefix could be discovered by means of the method defined in [RFC7050] only if the service provider uses DNS64 [RFC6147]. It may be the case Linkova & Jensen Expires 24 April 2025 [Page 10] Internet-Draft claton October 2024 that the service provider does not use or does not trust DNS64 [RFC6147] because the DNS configuration at the CE (or hosts behind the CE) can be modified by the customer. In that case, the service provider may opt to configure the NAT64 prefix by means of the option defined in [RFC7225]. This can also be used if the service provider uses DNS64 [RFC6147]. === 10. Security Considerations If a malicious actor spoofs PLAT presence signals (such as an RA with PREF64 option) or DNS responses for DNS-based NAT64 prefix detection ([RFC7050]), traffic of IPv4-only applications using CLAT can be affected: * if there is no PLAT (NAT64) devices, traffic to NAT64 destinations would be dropped. * If the attacker intercepts traffic for the NAT64 prefix (e.g. by providing the victim with a bogus NAT64 prefix and steering traffic for those destinations towards themselves), the attacker might be able to perform man-in-the-middle attacks. Using the PREF64 RA option to detect PLAT presence and the NAT64 prefix is less prone to such attacks than DNS-based detection ([RFC7050]), as the attacker needs to be on-link and be able to bypass layer-2 security features such as RA Guard. Therefore Section 5 recommends the PREF64 RA option as a preferred way to detect PLAT presence. In networks lacking explicit IPv6 deployment and consequently IPv6 security features, administrators may inadvertently expose link-local IPv6 connectivity when endpoints have IPv6 enabled. This unintended exposure can facilitate PLAT presence signal falsification, enabling malicious actors to conduct Man-in-the-Middle (MitM) or Denial-of- Service (DoS) attacks. This document mitigates this risk by requiring endpoints to disable CLAT when the network provides non- link-local IPv4 connectivity, as outlined in Section 6. 11. Privacy Considerations If the instance utilizes the same CLAT address for an extensive period of time or, much worse, uses the same CLAT address when connecting to different networks, eavesdroppers and information collectors can correlate various network activity to the same node. To mitigate that risk and make address-based network-activity correlation more difficult, each CLAT instance's source IPv6 address Linkova & Jensen Expires 24 April 2025 [Page 11] Internet-Draft claton October 2024 SHOULD be rotated the same way as temporary IPv6 addresses (see Section 7.2). It should be noted that the node's CLAT IPv6 address is only used (and visible to observers) when the traffic is carried from the CLAT node to the PLAT device. In the vast majority of the cases it means that address is never visible outside of the network Internet edge, so to perform address-based network-activity correlation the observer needs to be located in the same network as the CLAT node. To summarize, this document does not introduce any new privacy considerations. 12. IANA Considerations This memo does not introduce any requests to IANA. 13. References 13.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC3927] Cheshire, S., Aboba, B., and E. Guttman, "Dynamic Configuration of IPv4 Link-Local Addresses", RFC 3927, DOI 10.17487/RFC3927, May 2005, . [RFC6146] Bagnulo, M., Matthews, P., and I. van Beijnum, "Stateful NAT64: Network Address and Protocol Translation from IPv6 Clients to IPv4 Servers", RFC 6146, DOI 10.17487/RFC6146, April 2011, . [RFC6147] Bagnulo, M., Sullivan, A., Matthews, P., and I. van Beijnum, "DNS64: DNS Extensions for Network Address Translation from IPv6 Clients to IPv4 Servers", RFC 6147, DOI 10.17487/RFC6147, April 2011, . [RFC6333] Durand, A., Droms, R., Woodyatt, J., and Y. Lee, "Dual- Stack Lite Broadband Deployments Following IPv4 Exhaustion", RFC 6333, DOI 10.17487/RFC6333, August 2011, . Linkova & Jensen Expires 24 April 2025 [Page 12] Internet-Draft claton October 2024 [RFC6877] Mawatari, M., Kawashima, M., and C. Byrne, "464XLAT: Combination of Stateful and Stateless Translation", RFC 6877, DOI 10.17487/RFC6877, April 2013, . [RFC7050] Savolainen, T., Korhonen, J., and D. Wing, "Discovery of the IPv6 Prefix Used for IPv6 Address Synthesis", RFC 7050, DOI 10.17487/RFC7050, November 2013, . [RFC7335] Byrne, C., "IPv4 Service Continuity Prefix", RFC 7335, DOI 10.17487/RFC7335, August 2014, . [RFC8880] Cheshire, S. and D. Schinazi, "Special Use Domain Name 'ipv4only.arpa'", RFC 8880, DOI 10.17487/RFC8880, August 2020, . [RFC8028] Baker, F. and B. Carpenter, "First-Hop Router Selection by Hosts in a Multi-Prefix Network", RFC 8028, DOI 10.17487/RFC8028, November 2016, . [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, . [RFC8781] Colitti, L. and J. Linkova, "Discovering PREF64 in Router Advertisements", RFC 8781, DOI 10.17487/RFC8781, April 2020, . [RFC8585] Palet Martinez, J., Liu, H. M.-H., and M. Kawashima, "Requirements for IPv6 Customer Edge Routers to Support IPv4-as-a-Service", RFC 8585, DOI 10.17487/RFC8585, May 2019, . [RFC8925] Colitti, L., Linkova, J., Richardson, M., and T. Mrugalski, "IPv6-Only Preferred Option for DHCPv4", RFC 8925, DOI 10.17487/RFC8925, October 2020, . [RFC8981] Gont, F., Krishnan, S., Narten, T., and R. Draves, "Temporary Address Extensions for Stateless Address Autoconfiguration in IPv6", RFC 8981, DOI 10.17487/RFC8981, February 2021, . 13.2. Informative References Linkova & Jensen Expires 24 April 2025 [Page 13] Internet-Draft claton October 2024 [RFC1918] Rekhter, Y., Moskowitz, B., Karrenberg, D., de Groot, G. J., and E. Lear, "Address Allocation for Private Internets", BCP 5, RFC 1918, DOI 10.17487/RFC1918, February 1996, . [RFC4862] Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless Address Autoconfiguration", RFC 4862, DOI 10.17487/RFC4862, September 2007, . [RFC6145] Li, X., Bao, C., and F. Baker, "IP/ICMP Translation Algorithm", RFC 6145, DOI 10.17487/RFC6145, April 2011, . [RFC7225] Boucadair, M., "Discovering NAT64 IPv6 Prefixes Using the Port Control Protocol (PCP)", RFC 7225, DOI 10.17487/RFC7225, May 2014, . [RFC8900] Bonica, R., Baker, F., Huston, G., Hinden, R., Troan, O., and F. Gont, "IP Fragmentation Considered Fragile", BCP 230, RFC 8900, DOI 10.17487/RFC8900, September 2020, . [I-D.ietf-pquip-pqc-engineers] Banerjee, A., Reddy.K, T., Schoinianakis, D., Hollebeek, T., and M. Ounsworth, "Post-Quantum Cryptography for Engineers", Work in Progress, Internet-Draft, draft-ietf- pquip-pqc-engineers-05, 12 September 2024, . Appendix A. Enabling and Disabling CLAT: Flowchart Linkova & Jensen Expires 24 April 2025 [Page 14] Internet-Draft claton October 2024 +-----------------------------------------+ | | | | v | +----------------------------------+ +-----------------+------------+ | | YES | | | Has native IPv4 default route? +------> | CLAT Disabled | | | | | +------------------+---------------+ +------------------------------+ | NO ^ ^ +---------+-------------+ | NO | | | | | +--------v--------+ +-----------v------------+ +--+----------+ | | | | | NO | PLAT prefix | | | Start DHCP | | Received PREF64 in RA? +------>| discovered | | | | | | | via RFC7050?| | +---------+-------+ +-------------------+----+ +-------+-----+ | | ^ | | | | | | YES | | v | v | YES | +---------------------+ | +---------------+ | | | | | | | | | | Wait for DHCP Offer |<----+------+ Enable CLAT |<---------+ | | | | | | | +----------+----------+ | +---------------+ | | | | | | | v | YES | +---------------------+ | | | | | | | +-----+ | | Option 108 Present? | | | | NO | | +--------------------------------------------------+ +---------------------+ Figure 1: Enabling and Disabling CLAT Instance Acknowledgements Thanks to Ondrej Caletka, Stuart Cheshire, Lorenzo Colitti, Jeremy Duncan, Jason Healy, Ed Horley, KAWASHIMA Masanobu, Ted Lemon, George Michaelson, Jordi Palet, Dieter Siegmund for the discussions, the input, and all contribution. Authors' Addresses Linkova & Jensen Expires 24 April 2025 [Page 15] Internet-Draft claton October 2024 Jen Linkova Google 1 Darling Island Rd Pyrmont NSW 2009 Australia Email: furry13@gmail.com, furry@google.com Tommy Jensen Microsoft Email: tojens@microsoft.com Linkova & Jensen Expires 24 April 2025 [Page 16]